Renewable Design for Celular Repetidor Booster - lte repeater band4 network booster 4g mobile signal booster 2600 – Kingtone Detail:
- Introduction
- Mainfeature
- Application&scenarios
- Specification
- Parts/Warranty
-
A cell phone signal booster (also known as cellular repeater or amplifier) is a device that boosts cell phone signals to and from your mobile phone whether at home or office or in any vehicle.It does this by taking the existing cellular signal, amplifying it, and then broadcasting to an area in need of better reception.A booster kit includes an booster, an indoor antenna and an outdoor antenna, the outdoor antenna can pick up good mobile signal from outside of your house, and send the signal through coaxial cable to the booster, the booster can amplify the signal, then the amplified signal is sent to the indoor antenna, the indoor antenna can transmit the signal into your house, so you can enjoy clearer phone call or faster mobile date inside your house.The consumer repeater is an ideal solution for providing a cost effective improvement in cellular in-building coverage of a home, office, restaurant or building, in the quickest time possible.Preparing to Buy a Booster:1. Check your frequency, because different Phone Providers operate on different frequencies and the booster can only work on correct frequency.For more detail, refer to www.unlockonline.com/mobilenetworks.php2. Make sure that you can place calls on the outside of your home, in the attic, at roof level or wherever you plan to place the Outdoor Antenna. Phonetone can only bring signal into your home when signal reaches the Outdoor Antenna. If there is no signal, the Phonetone will not work for you.
- Mainfeature
-
Main Features:1. With unique appearance design, have good cooling function2. With MGC function,(Manual Gain Control), Customer can adjust the Gain as needed ;3. With DL signal LED display, help to install the outdoor antenna at the best state;4.With AGC and ALC, make repeater work stable .5.PCB with isolation function ,make UL and DL signal not influence each other,6.Low intermodulation, high Gain ,stable Output power
- Application&scenarios
-
22Outdoor antenna ( for receiving the signal from the BTS ) + Cable ( transfering the received signal) + Repeater ( for amplifying the received signal) + cable( for transfering the amplified signal) + indoor antenna( for shooting the amplified signal)(Note : Omni indoor antenna is 3dBi,it can work with about 200m2 . If need repeater coverage larger area , need add moreantenna,the KT-4G27 Max can work with 8pcs indoor antenna. ( when add antenna ,please remember to take splitters )Installation Approaches:Step 1 Start by taking your phone up to the roof or other location outside to find where the signal is strongest.Step 2 Temporarily mount the Outdoor (outside) antenna in that location. You may need to adjust and move the antenna later.Step 3 Run coaxial cable into the building to a convenient loaction (attic, etc.) where you can also get standard power for the 3G Signal Booster .Step 4 Place the Signal Repeater in that location and connect the coaxial cable to the Outdoor Side of the Signal Repeater and the Outdoor antenna.Step 5 Mount your Indoor (inside) antenna in a productive location. You may need to adjust or move the antenna later. More notes on Indoor antennas and patterns here.Step 6 Connect coaxial cable between the Indoor antenna and the Signal Repeater output port.Step 7 Power up the system and check for signal inside the building. If needed, tune system by moving and or pointing the Outdoor and Indoor antennas until they get the most signal possible.Step 8 Secure all antennas and cables, securely mount the Signal repeater and clean up the installation.Step 9 Plug power adaptor into AC power socket and finish installation
- Specification
-
Electrical specification
Uplink
Downlink
Frequency Range
4G LTE
2500~ 2570 MHz
2620 ~ 2690MHz
Max .Gain
≥ 70dB
≥ 75dB
Max .Output Power
≥ 24dBm
≥ 27dBm
MGC ( Step Attenuation )
≥ 31dB / 1dB step
Automatic Level Control
≥ 20dB
Gain Flatness
GSM & CDMA
Tpy≤ 6dB(P-P); DCS,PCS ≤ 8dB(P-P)
WCDMA
≤ 2dB/ 3.84MHz,Full Band ≤ 5dB(P-P)
Noise Figure
≤ 5dB
VSWR
≤ 2.0
Group Delay
≤ 1.5μs
Frequency stability
≤ 0.01ppm
Spurious Emission &
Output inter-modulationGSM Meet ETSI TS 151 026 V 6.1.0
WCDMA Meet 3GPP TS 25.143 ( V 6.2.0 )
CDMA Meet IS95 & CDMA2000
WCDMA System
Spurious Emission Mask
Meet 3GPP TS 25.143 ( V 6.2.0 )
Modulation Accuracy
≤ 12.5%
Peak Code Domain Error
≤ -35dB@Spreading Factor 256
CDMA System
Rho
ρ > 0.980
ACPR
Meet IS95 & CDMA2000
Mechanical Specifications
Standard
I /O Port
N-Female
Impedance
50 ohm
Operating Temperature
-25ºC~+55ºC
Environment Conditions
IP40
Dimensions
155x112x85mm
Weight
≤ 1.50Kg
Power Supply
Input AC90-264V,output DC 5V / 3A
LED Alarm
Standard
Power LED
Power Indicator
UL LED
Be lighted when there is phone calling
DL 1
Be lighted when Outdoor signal is -65dB
DL 2
Be lighted when Outdoor signal only -55dB
DL 3
Be lighted when Outdoor signal only -50dB
- Parts/Warranty
-
2Package Included:1 * lte repeater band4 network booster 4g mobile signal booster 26001 * Power Adapter1 * Mounting Screw Kit1 * English User ManualNote : The product is not including cable,outdoor antenna,indoor antenna,you need to buy extra
■ contat supplier ■ Solution&Application
-
*Model : KTWTP-17-046V
*Product Category : (450-470MHz) 17dBi-1.8m grid parabolic antenna -
*Model : KT-CRP-B5-P33-B
*Product Category : UHF 400Mhz 2W Band Selective walkie talkie Repeater -
*Model : KT-CPS-400-02
*Product Category : 400-470MHz 2-way Cavity splitter -
*Model :
*Product Category :
-
Product detail pictures:
Related Product Guide:
What is MIMO?
We insist on offering high quality production with good business concept, honest sales and the best and fast service. it will bring you not only the high quality product and huge profit, but the most significant is to occupy the endless market for Renewable Design for Celular Repetidor Booster - lte repeater band4 network booster 4g mobile signal booster 2600 – Kingtone, The product will supply to all over the world, such as: Mongolia, Poland, United States, Based on experienced engineers, all orders for drawing-based or sample-based processing are welcomed. We have won a good reputation for outstanding customer service among our overseas customers. We will continue to try the best to offer you good quality products and the best service. We are looking forward to serving you.
By Dinah from Turkey - 2018.10.01 14:14
With a positive attitude of "regard the market, regard the custom, regard the science", the company works actively to do research and development. Hope we have a future business relationships and achieving mutual success.
By Frances from Lisbon - 2018.06.12 16:22